在干式地面辐射系统中插入干式系统板
| 产品 | InstalSystem 5 |
| 文章类型 | 功能和工具 |
| 版本的最新内容 | IS 5.0 Beta Rev. 5.B1 |
说明
这个功能能够插入干式系统板 部件并作为在带有导向板的干式地面辐射系统中管材铺设的基础。
干式系统板 部件可以任意布置，且可剪裁以适应房间的几何形状，而剪裁后的剩余部分也能够被使用。
在完成可计算后，就生成可一个辐射供热部件清单 ，指出了项目中所用的干式系统板材的数量。
程序中的位置
- 干式系统板 的命令图标 - 当打开干式系统 编辑范围时，在主工具 条的辐射 组中就可看到该命令图标。
- 其它指定类型的干式系统板的命令图标，则取决于软件包的配置。
应用举例
手动插入干式地面辐射系统中的干式系统板
- 仅在 地面供热/供冷区 插入干式系统板
更多信息，见： 供热/供冷区
必须在这个步骤之前进行必要的设计操作。更多信息，见： 地面和墙面辐射系统的设计 以及在一般参数 窗口内的地面系统 中，从默认的系统/固定方式 选项中选择 "干式系统" - 当插入干式系统板 之前，应在参数表 窗口中选择适宜的目录。要考虑管间距和指定区域的管间距。
当所使用的软件包带有特定的工具栏时，就有可能选择某一特定类型的系统板图标命令。 - 在捕捉 模式下，支持插入干式系统板 部件 、房间的轮廓以及干式板本身。更多信息，见： 其它信息
- Using cut off pieces of 干式系统板 components.
The portion of 干式系统板 component being inserted that extends beyond 房间 or overlaps the 干式系统板 inserted before is automatically cut off. The cut off piece can be used in the project and the corresponding number of 干式系统板 components used is included in the bill of materials. The cut off pieces can be pasted outside of the drawing and reinserted elsewhere within the 地面供热/供冷区 cut to fit the edge provided that 剪切 and 粘贴 functions are used.
Adjusting the line dividing the 地面供热/供冷区 into 供热/供冷地面 components
- The lines dividing the 地面供热/供冷区 into 供热/供冷地面 components determined automatically may not match the edges of 干式系统板 components inserted manually. In order to match these the dividing line has to be adjusted.
更多信息，见： Manual indication of the dividing line
更多信息，见： Modifying the dividing line after automatic division
3. Adjustment of the dividing line
Inserting loop drawings
After proper arrangement of the dry system plates it is necessary to manually lay out the loops in accordance with 更多信息，见： Manual editing of loop drawings in dry systems with guide plates
Additional information
When inserting and copying/pasting a 干式系统板 component it is possible to switch between active edges/snap points:
TAB - cursor moves clockwise
Shift+TAB - cursor moves anticlockwise
- If an edge is active on a 干式系统板 component being inserted (cursor in the centre of the edge) - then 3 points are activated: 1 in the centre and 2 in corners.
- If individual points are active on a 干式系统板 component being inserted, the program switches between edge points of the component grid and snaps onto the grid points of other 干式系统板 components.
- Copying of several 干式系统板 components: the program switches between subsequent snap points of 干式系统板 components that make up the block being copied.
- Moving a 干式系统板 component: the active edge or point is selected based on the "grab" location of the component, and changing with the "Tab" key is disabled.